How-to guide · 5 min read

How to Snow Foam Your Car

The first step of a safe wash: how to mix snow foam, how long to leave it, and what to do next.

By the Cleanazfk studio team, Ravenhall

How to Snow Foam Your Car

Snow foam is a pre-wash. You cover the car in thick foam, let it sit and soften the dirt, then rinse most of the grit away before a wash mitt ever touches the paint. Less grit dragged across the paint means less risk of swirl marks and hazing. This is how we do it in the studio, and it works just as well in your driveway.

What you need

How to snow foam, step by step

  1. Park in the shade. Start with cool panels, out of direct sun. Foam that dries on hot paint can leave spots, so early morning or late afternoon is best.
  2. Mix your foam. Add 900ml of warm water and 100ml of Super Snow Foam to the bottle (1:10) and give it a shake. Going easy? 50ml in 950ml works too.
  3. Cover the car. Work from the bottom up so the dirtiest lower panels get the longest soak, then the roof, glass and bonnet. You want a thick, even blanket.
  4. Let it dwell for 4 to 5 minutes. Watch the foam slowly slide down and carry dirt with it. On a warm day, rinse a little sooner rather than letting it dry.
  5. Rinse from the top down. Get into the wheel arches, sills, door shuts and behind the number plate, where grit hides.
  6. Wash with two buckets. Fill one bucket with 50ml of Bubbly Wash & Wax per 5L of water and the other with clean water. Wash a panel, rinse the mitt in the clean bucket, then go back to the soap. Top to bottom, one panel at a time.
  7. Dry straight away. Use a soft drying towel like the Baby Daddy drying towel before water spots can form.

Want water to bead off?

Finish with SiO2 Ceramic Foam. Mix it the same way (100ml in 900ml of warm water), foam it on, leave it 4 to 5 minutes and rinse. It leaves a slick, glossy layer of protection.

Foam cannon or hose foam gun?

A foam cannon connects to a pressure washer. It makes the thickest foam and lets you dial it from thick to wet. A hose foam gun runs straight off your garden hose, so it's the easy option if you don't own a pressure washer. Super Snow Foam works in both, mixed the same way.

Foam coming out runny?

  • Use warm water and the full 100ml of foam.
  • Turn the cannon's foam dial towards thick.
  • Check your pressure washer's rating. A cannon's standard inlet needs enough pressure to foam properly. If you have a Cleanazfk Snow Foam Cannon and your washer is rated under 1700 PSI, swap the 1.25mm inlet for our 1.1mm inlet.
  • New pressure washer? We stock pressure washer adaptors for over 25 models, including Karcher, Gerni, Ryobi, Bosch, Nilfisk and Stihl, so a Cleanazfk cannon connects straight on.

Questions we get asked

Do I need a pressure washer?

No. A foam gun on your garden hose works too. A pressure washer and cannon just give you thicker foam.

Is snow foam enough on its own?

For light dust, a foam and rinse can be enough. For a proper clean, follow it with a two-bucket wash so the mitt lifts what the foam softened.

Can I use dishwashing liquid instead?

We don't recommend it. Dishwashing liquid is made to strip grease, and on a car it can strip your wax or sealant too.

How much Super Snow Foam do I need?

100ml per 1L fill for thick foam, or 50ml if you want to stretch it. A 1L bottle gives you 10 full-strength fills.

Rather we did it?

Bring it to the studio

Detailing, paint correction, ceramic coating, PPF and window tint at our Ravenhall studio. Tell us about your car and we'll send you a quote.

Get a quote

Shop this guide

  • 20% offStep 1 · Pre-wash
    Super Snow Foam Pre-Wash

    Super Snow Foam Pre-Wash

    From $9.50From $7.60$9.50

  • 20% offStep 2 · Wash
    Bubbly Wash & Wax Shampoo

    Bubbly Wash & Wax Shampoo

    From $7.50From $6.00$7.50

  • 20% offStep 3 · Protect
    SI02 Ceramic Foam Superior Protectant

    SiO2 Ceramic Foam Superior Protectant

    From $15.50From $12.40$15.50